Matlab 2017b installation (linux)

-

1. Create a folder with all installation files

(1) MATLABR2017b_Linux_Crack
(2) install_key.txt
(3) R2017b_glnxa64.iso

-> Download

2. mount R2017b_glnxa64.iso and install (refer to install_ket.txt)

sudo mount -t auto -o loop R2017b_glnxa64.iso /temp
cd temp
sudo ./install


3. After installation, copy licences to specific directories...

cd MATLABR2017b_Linux_Crack/
sudo cp  license_standalone.lic /usr/local/MATLAB/R2017b/licenses/
 sudo cp  libmwservices.so /usr/local/MATLAB/R2017b/bin/glnxa64/

4. Unmount

sudo umount temp

5. Run

cd /usr/local/MATLAB/R2017b/bin
sudo ./matlab

Reference:
1. ubuntu16.04安装MATLAB R2017b步骤详解（附完整破解文件包）

留言

  1. 胡2019年7月24日 清晨6:26

    R2017b_glnxa64.iso 下载失效了，博主可以重新分享下吗

    回覆刪除
    回覆
    1. 胡2019年7月25日 晚上11:52

      今天安装好啦。最后还是重新去百度网盘下载的😂😂
      https://pan.baidu.com/s/1wijZCXIWsNXgz0yYYBXHnQ#密码 e8b2

      刪除
    2. Chuang2019年7月29日 凌晨2:40

      OK! 搞定就好!

      刪除

張貼留言

這個網誌中的熱門文章

Useful PX4 Parameters

-
1. For setting companion link SYS_COMPANION (Before ver. 1.9.0) MAV_0_CONFIG, MAV_0_MODE (After ver. 1.9.0) 2. EKF2 configuration EKF2_AID_MASK EKF2_HGT_MODE EKF2_EV_DELAY (Reduce this parameter if high rate external vision is available) EKF2_EV_POS_X, EKF2_EV_POS_Y, EKF2_EV_POS_Z 3. Offboard mode parameters ( The vehicle will exit the mode if target setpoints are not received at a rate of > 2Hz ) COM_OBL_RC_ACT (Default: position mode, I set land mode) COM_OBL_ACT COM_OF_LOSS_T 4. Position loss failsafe COM_POSCTL_NAVL 5. Land mode MPC_LAND_SPEED COM_DISARM_LAND: Time-out for auto disarm after landing. (Default: 0, I set 3.) 6. TBD Reference: [1]  https://dev.px4.io/en/advanced/parameter_reference.html [2]  https://dev.px4.io/en/ros/external_position_estimation.html#tuning-EKF2_EV_DELAY [3]  https://docs.px4.io/en/config/safety.html#qgc_safety_setup
閱讀完整內容

Tuing PID parameters in QGroundcontrol (2)

-
圖片
Based on tips for tuning PX4 PID parameters written in my previous post [1] or even using the default values directly, you will be able to fly your vehicle freely in manual or stabilized flight mode.   However, if you are using an unique vehicle (usually assembly by yourself and only equipped with sensors you desire) and struggling for finding the best PID parameters for your applications. I think following 8 tips will help you to get ideal PID parameters.  This is the vehicle I made based on LHI QAV250 fiber frame, with TX2, high-speed camera, etc.[2]  Tip1:  Tuning order: Rate controller -> attitude controller -> position controller The PX4 controllers are layered [3], which means a higher-level controller passes its results to a lower-level controller. Thus the PID tuning needs to be done from lowest-level controller to highest-level controller. Tip2:  Check if  PWM_MIN  is set correctly. Remove propellers Arm the vehic...
閱讀完整內容

Matlab Pixhawk Support Package installation (Windows)

-
圖片
1. Download the pixhawk support package [1] 2. Open MATLAB R2017b and navigate to the file location. 3. Click "PX4PSP_v3_0_4_351_R2017b" and install it 4. Create a folder for firmware download path (ex: D/PX4) 5. Setting bash environment for windows 10 [2]  (1) Active "Windows subsystem for linux" (2) Download and install Ubuntu (3) Using the terminal like in Ubuntu environment ex: 6. Install all necessary toolchain with " windows_bash_nuttx.sh " [3] or using Cygwin Toolchian [4] or [5] (python27 would show in following folder) 7. Key in command " PixhawkPSP(' D:\PX4 ') " in the Matlab 8. Make sure windows 10 bash and python path are correct => Validate paths 9. Download firmware to the folder we specify before and then validate firmware. 10. Selecting cmake configuration [6] 11. Build firmware *Error: make command not found   Solution: [7] T...
閱讀完整內容